Infinity Chinese Miracle-2 _Cm2_update New Here

Infinity Chinese Miracle-2 MTK/Mediatek v2.00 r3 - More secured devices and features !

- Main
DownloadAgent version 1816 supported and tested on all supported SoC.
Fixed some memory leaks
Connection level revised

- MemoryTool
Fixed multi-selection
GPT init revised
Preloader init revised

- Service
Repair Security revised. Fixed issues with some Meizu and other models.

- Core
Optimized different agents versions support ( DA16xx line )
EMIDB updated
Hint/Error explain module updated
Activated SymLinks - allow reduce boot base size by redirecting diffirent brand/models if they have same base
BootHelper ( stage 1 of 3 ) activated - hints/explanation of boot sequnce and correct file selection
MT6758 support under test
MT6771 support under test
MT6765 support under test

- Flasher
Show Preloader HW compatibility when load firmware in flash tab
Fixed file selection order - if SW package contain mixed types - secure will be selected by default

- FW reader
New types of firmwares supported
Scatter creation optimized for some SoC

- New models included
Limited Alcatel support
Limited Gionee support
Limited Wiko support
Limited Tecno support
And diffirent other models
Some other basic "generic" secure devices support optimized
NAND devices on MT6570 moved to separate mode ( under base ) - FACTORY for ONLY FACTORY-provided FW flashing, INFINITY - for all rest operations

Known issues/warnings/info :
1. [NAND on MT6570] v1712,v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE!!!
Preloader info shown now during FW load.

Credits :
gracy_elec - different useful files contribution
kamal_singla - testing and useful files contribution
merujeffrey - useful files contribution and report logs


Download link #1 - Download link #2 - Download link #3

 

nfinity Chinese Miracle-2 MTK/Mediatek v2.00 r4 - MT6771 support and other features

​

Infinity Chinese Miracle-2 MTK/Mediatek v2.00 r4 - MT6771 support and other features !

Important:
- Software installed to new folder /CM2MT2/ and designed to support new models
- Smart-Card firmware v0136 is Ok to use this version
- DO NOT uninstall previous version 1.58 ! If you are trying to connect phone with new software and see a message like LEGACY MTK you should use version 1.58 for this device !

- Main
Connection level revised
BROM level support optimized

MT6771 CPU supported!
MT6771 moved from TEST to GENERAL support.
Firmwware read
Firmware write
NVRAM read
NVRAM write
Reset Settings / Format FS
Reset FRP
Reset Privacy
MemoryTool

- Service
Repair Security revised. Fixed issues with some NV types.

- Core
EMIDB updated
Hint/Error explain module updated
MT6758 support under test
MT6765 support under test

- FW reader
MT6771 supported
New types of firmwares supported
Scatter creation optimized

- SP Unlock
Revised unlock support for some models
Info: MT6739/MT6763/MT6771 IS NOT supported YET!

- New models included
Limited Oppo support (F7/A3)
Limited Vivo support
And diffirent other models
Some other basic "generic" secure devices support optimized

Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages SHOULD NOT BE USED due to these packages have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal behaviour and can not be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices (except SYSTEM/CACHE/USER) may fail ! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases !
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY BE DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE !
Preloader info shown now during FW load.

Credits :
kamal_singla - testing and useful files contribution





Discussion and download links - https://www.infinity-box.com/support/?r=100016

 

Infinity Chinese Miracle II SCR/SPD-RDA v1.03: New models and features

Infinity Chinese Miracle II SCR/SPD-RDA v1.03: New models and features


Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C), SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826

RDA Mirco RDA8851 rev A,B,C,L,CL/RDA8826
Flashing protocol updated
Updated LOD tools ( flashing / customizing )

Spreadtrum SC6533/G:
Protocol updated
Support for REV2 bootrom mode activated
FW reading revised
Updated LOD tools ( flashing / customizing )

Spreadtrum SC6530/6531/A/C/E:
Revised Repair security feature
Flashing revised
-> Activated "Format FFS" during BINARY dump writing
-> Use that feature, if device not allow make direct format ( some C/E revision devices )
User code read revised - activated 2nd mode : from DUMP
-> Press and hold LEFT SHIFT key, while starting ReadUsercode code operation. Select desired dump file to read code.
Activated AUTO fixer for memory dumps
Internal loaders updated

Spreadtrum other:
Protocol updated
PAC handling revised
Improved Flashing procedure for SC7701/SC7702 devices
Improved Flashing procedure for SC6825/SC8825 devices

Known issues[*]/warnings[!]/info:
1. AUTO fixer for memory dumps
-> That feature will AUTOMATICALLY FIX dumps from devices with "abnormal" flash and memory layout ( issue found on number of devices 16MB flash with 8MB layout )
-> Just select binary dump in flashing tab or any other operation, which require file select.
2. [*] In some cases Format FFS may fail on E and C rev
-> Read Flash Dump, write it back. During Dump writing SW will ask you about FormatFFS.






Download link

 

Infinity `SM` software v2.00 released

Infinity `SM` software v2.00 released

Infinity Samsung Activation server is back with new Smart-Card firmware for latest `SM` software release.
`SM` software v1.xx was released time ago as a free software for Infinity users. From now v2.00 released as a paid addon.
Users who have made free Infinity `SM` activation can use it in future with `SM` software v1.xx. If users of free `SM` Activation want to use `SM` software v2.xx they should obtain new `SM` activation.

Infinity `SM` software v2.00 news:
- many internal stability improvements
- FRP unlock engine re-written
- FRP unlock procedure updated
- security area write for MTK based devices
- security area write for Exynos based devices
- Smart-Card firmware should be updated to use this software release
- "SM ResourcePack" should be installed to get all released functions working

At the moment there is a special offer for `SM` v2.xx Activation. Price is quite cheap right now but with each new `SM` update released price will be higher than before. So you can activate software right now for a cheap price or you can wait some time, see software updates progress and then pay higher price for it.


Download link

 

Infinity `SM` software v2.01 released

Infinity `SM` software v2.01 released


- Service - add `Read Log` option for unlock Exynos phones via server
- some bug fixed


More information about software and activation process is here - https://www.infinity-box.com/support/?r=100034
Information about supported models and functions - https://www.infinity-box.com/support/?r=100035
Test reports - https://www.infinity-box.com/support/?r=100009



Download link

 

Infinity `SM` software v2.02 released

Infinity `SM` software v2.02 released

Service changes:
- Downgrade modem procedure released. This operation may be dangerus so use at own risk and only if you are really know you need it !
- rebuild Reset FRP procedure
Internal changse:
- a lot of changes related to use server functions
- bug fixes and internal improvements





Download link

 

Infinity `SM` software v2.00 released

Infinity `SM` software v2.00 released

Infinity Samsung Activation server is back with new Smart-Card firmware for latest `SM` software release.
`SM` software v1.xx was released time ago as a free software for Infinity users. From now v2.00 released as a paid addon.
Users who have made free Infinity `SM` activation can use it in future with `SM` software v1.xx. If users of free `SM` Activation want to use `SM` software v2.xx they should obtain new `SM` activation.

Infinity `SM` software v2.00 news:
- many internal stability improvements
- FRP unlock engine re-written
- FRP unlock procedure updated
- security area write for MTK based devices
- security area write for Exynos based devices
- Smart-Card firmware should be updated to use this software release
- "SM ResourcePack" should be installed to get all released functions working

At the moment there is a special offer for `SM` v2.xx Activation. Price is quite cheap right now but with each new `SM` update released price will be higher than before. So you can activate software right now for a cheap price or you can wait some time, see software updates progress and then pay higher price for it.

Latest released version: 2.03
Curent price: 70 Infinity credits


List of supported models and features for previous software release - Infinity `SM` software - general information, models, functions etc.
Test reports are here - Success test reports with Infinity SM software


Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.01 - LEGACY support and other features

Infinity Chinese Miracle-2 MTK/Mediatek v2.01 - LEGACY support and other features

Important:
- Software installed to new folder /CM2MT2/ and designed to support new models

Legacy core support activated:
MT6571
MT6572
MT6580
MT6582
MT6589
MT6592
MT6595
MT6597
MT6732
MT6735
MT6737
MT6752
MT6753
MT6795
MT8127
MT8163
MT8321
MT8732
MT8735
MT8752

Identify: full device info, security info
Flash Factory Firmware
Read Factory Firmware
Reset Settings / Format FS
Reset FRP
Repair Security (Flash Mode, Direct)
SP unlock
MemoryTool - complete device control, service, repair, forensic etc.

- Main
Loader database optimized, size reduced.
DA v1820 line support tested and activated
DA v1836 line support tested and activated
Connection level revised
BROM level support optimized
Optimized and changed HighSpeed port selection
FlashEngine revised
NVRAM tool revised
Global option PWM - allow switch SW between two different work modes for RAPHAEL.
> Use second one if first mode give errors at writing f.e. restore NVRAM on F5 like device etc.
> For LEGACY phone it used in MEMORY TOOL ( WRITE / WIPE )

- Service
Repair Security revised
> Old LEGACY types require FORMAT FS/FACTORY RESET for accept changes !
Format FS - new mode activated: Forced Erase
Format FS - fixed WIPE mode

- Core
EMIDB updated
New EMI engine for LEGACY line
> EMI engine support almost all existing LEGACY line
> New types for RAPHAEL included

- FW reader
LEGACY core supported ( unsigned and static signed types are supported )
New types of firmwares supported
Scatter creation optimized

- Other
Settings tab activated ( firmware path settings and other features can be found here )
AutoUpdate ( module files ) feature activated

Many other changes and fixes

Known issues/warnings/info:
1. FileSystem flashing on some SBC-enabled RAPHAEL devices (except SYSTEM/CACHE/USER) may fail ! Solution - exclude them from flashing list.
2. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list !
3. MT6589 supported ONLY up to DAv17xx line, after DAv1728 support has been removed.
4. MT6592 support on DAv18xx loader line broken ( DA issue )
5. EMI/DRAM init module in LEGACY line is almost auto, but in some case require CHANGE EMI setting, if used internal DB ( since much RAMsize/Revision of eMMC/eMCP )
6. MOST of LEGACY phone can be booted via BROM mode from now ( PLAIN, PRL, SBC )
7. NAND support on LEGACY line is not activated yet




Discussion and download links are here

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.02 - new features, loaders, improvements

Infinity Chinese Miracle-2 MTK/Mediatek v2.02 - new features, loaders, improvements

- Base
Base - Read info from EMI base (preloader) in manual mode after selection
Base - Info reading improved ( in some cases device info can be empty )
Base - Manual mode selection revised ( Boot fail issues in manual mode )

- MemoryTool
MemTool - Partition types detection improved
MemTool - Interface changes ( partition selection style changed, menu sctructure changed )
MemTool - work with boot1/boot2 section revised for LEGACY line
MemTool - InitPreloader option activated ( LEGACY/RAPHAEL )
MemTool - Flash service regions read/write now allowed ( if they not set as protected - i.e. OTP )

- Flasher
Flasher - Removed "Skip preloader" option, use selection instead ( untick preloader from flashing list )
Flasher - Customization model revised
Flasher - DL Fix / ADL Checksum revised
Flasher - Preloader initialization during flashing revised
Flasher - More accurate PMT/GPT rebuild, for compatibility with SPFT ( PMT invalid issues after servicing with MT2 module )

- Firmware Reader
FWReader - Scatter compatibility for spft optimized (6735, 6737)
FWReader - More types supported for safe read
FWReader - Info reading improved ( in some cases device info can be empty )
FWReader - SW path settings also accepted now on FW read

- Platform changes
Platform - MT6589 support optimized
Platform - MT6592 support optimized
Platform - MT673x support optimized

- Loader database
LoaderDB - New agents included ( BQ, TECNO, INFINIX, VIVO )

- Other
Other - Lot of small fixes and changes, reported by users

Thanks to : gracy_elec, kamal_singla and other our users for providing files and/or testing


Download link

 

Infinity Samsung `SM` v2.05 released

Infinity Samsung `SM` v2.05 released



Service: added new version of Reset FRP procedure (without user-data lost)

How to use: check "new" checkbox and follow instructions







Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.03 - MT817x Series support, new features
Base:
Base - DA v1844 support tested on all platforms
Base - MT8172 support activated
Base - MT8173 support activated
Base - MT8176 support activated
Base - Info reading improved ( in some cases device info can be empty )
Base - Startup issues on some machines fixed
Base - Autoupdate feature revised
MemoryTool:
MemTool - Partition types detection improved
MemTool - InitPreloader option revised
Flasher:
Flasher - Activated flashing support for LEGACY signed FW types ( ver3, ver4 )
Flasher - Customization model revised
Flasher - DL Fix / ADL Checksum revised
Flasher - Cheksum issue on 6572/6582 fixed
Flasher - MT6570 NAND support fixed
Flasher - Flashing support for secure FW readout from LEGACY signed devices ( fused )
Flasher - More info, state and other debug stuff during secure types flashing
FWReader:
FWReader - Activated reading for LEGACY secured phones ( for fused devices )
FWReader - Secure state and signature type info during reading
FWReader - Secure workaround for cpu-paired security on fused devices ( FW completey safe for flashing )
FWReader - More types supported for safe read
FWReader - Info reading improved ( in some cases device info can be empty )
Other:
Other - Preloader parsing issues with some new platforms fixed
Other - Lot of small fixes and changes, reported by users
Other - BootHelper updated
Service:
Service - Security repair revised
Service - FixDL option activated
Service - Format FS revised, ENCRYPTION issues, bootloop issues fixed on some platforms/devices
Platform:
Platform - MT8172 support activated
Platform - MT8173 support activated
Platform - MT8176 support activated
Platform - MT2601 support activated
Platform - MT6582 support optimized
Platform - MT6572 support optimized
Loaders:
LoaderDB - New agents included (Teksun, Lenovo, Tecno, CAT, COMIO, Gionee)
Thanks to : kamal_singla, gracy_elec and other our users for providing files and/or testing


Download link

Subscribe to Telegram channel and get news faster !

Infinity-Box 13 years (2005 - 2018) updates and support as nobody else - News
Twitter - Facebook - Telegram

 

Infinity `SM` software v2.00 released

Infinity `SM` software v2.00 released

Infinity Samsung Activation server is back with new Smart-Card firmware for latest `SM` software release.
`SM` software v1.xx was released time ago as a free software for Infinity users. From now v2.00 released as a paid addon.
Users who have made free Infinity `SM` activation can use it in future with `SM` software v1.xx. If users of free `SM` Activation want to use `SM` software v2.xx they should obtain new `SM` activation.

Infinity `SM` software v2.00 news:
- many internal stability improvements
- FRP unlock engine re-written
- FRP unlock procedure updated
- security area write for MTK based devices
- security area write for Exynos based devices
- Smart-Card firmware should be updated to use this software release
- "SM ResourcePack" should be installed to get all released functions working

At the moment there is a special offer for `SM` v2.xx Activation. Price is quite cheap right now but with each new `SM` update released price will be higher than before. So you can activate software right now for a cheap price or you can wait some time, see software updates progress and then pay higher price for it.

Latest released version: 2.06
Curent price: 85 Infinity credits


List of supported models and features for previous software release - Infinity `SM` software - general information, models, functions etc.
Test reports are here - Success test reports with Infinity SM software


Download link

 

Infinity CM2MT2 v2.04: New chips and features activated !
Base:
Base - MT6761 support activated
Base - MT6765 support activated
Base - MT6771 support activated
Base - Secure boot - ARB verification during boot ( via BROM logging )
Base - Secure boot - SLA challenge state verify ( pass-trought file or nonce challenge )
FWFlasher:
FWFlasher - Some ancient secure devices flashing optimized ( early 6572 and similar )
FWFlasher - MT6753/MT6752 flashing revized
FWFlasher - Pre-flash backup option enabled
FWFlasher - Flash core updated

FWReader:
FWReader - More accurate FW verification for signed types ( issues after FOTA "garbaging" )
FWReader - ARB state and version, if present ARB bit
FWReader - AVB state and version, if present AVB secure mechanism
FWReader - FW logging info - if SW show it during load - make sure device contain SAME or LOWER version!
FWReader - More types supported for safe read
FWReader - Info reading improved

Service:
Service - Security repair revised ( NVRAM verify and some "old" types support )
Service - "Repair BaseBand" option activated
Service - Format FS revised
Service - NVRAM module updated
MemoryTool:
MemTool - Improved work with partitions on LEGACY line
MemTool - Wipe operation optimized ( def and adr mode )
Platform:
Platform - MT6761 support activated [ Under test ]
Platform - MT6771 support activated
Platform - MT6765 support activated
Platform - MT6753 support optimized
Platform - MT8172 support optimized
Platform - MT8176 support optimized
Platform - MT8163 support optimized
Platform - MT8127 support optimized
Loaders:
LoaderDB - New agents included ( Moto, Huawei, ZTE, Asus and others )

Other:
Other - Lot of different small changes and fixes
Other - BootHelper updated
Other - ErrorHandling updated - more detailed hints/explanation of troubles during service process
Other - EMI Module updated - MT6765/MT6771/MT8176/MT8172/MT8173/MT6753 supported
Other - Automatic backup during Identify and critical operations ( list can be tuned via edit settings.ini )
Other - Partial LEGACY NAND support ( complete boot/verify ) for testing purposes for now - MT6580, MT81xx series
Other - All settings ( except FLASH tab and Platform Settings group ) now saved/load automatically

Many thanks to: bRkA, gracy_elec and other our users for providing files and/or testing

Download link

Subscribe to Telegram channel and get news faster !

Infinity-Box 14 years (2005 - 2019) updates and support as nobody else - News
Twitter - Facebook - Telegram

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.05 - New models and features

Base:
Base - Secure boot - ARB verification revised for some secure configs and chips

FWFlasher:
FWFlasher - Flash core updated
FWFlasher - SecureFlash on Legacy phones revised ( SECCFG options and other issues fixed )
FWFlasher - MT6753/MT6752 flashing revised

FWReader:
FWReader - More accurate type detection on LEGACY lines
FWReader - More types supported for safe read
FWReader - Info reading improved

Service:
Service - "SimLock Reset" option activated - used to rollback all LockSettings to default
Service - Format FS revised
Service - Repair BB revised
Service - NVRAM module updated

Platform:
Platform - MT6771 support optimized
Platform - MT6753 support optimized
Platform - MT8127 support optimized

Loaders:
LoaderDB - Lot of new agents included (Alcatel, Moto, Lava and others)

Other:
Other - Many different small changes and fixes
Other - Some kind of GUI changes for better user expirience
Other - ErrorHandling updated - more detailed hints/explanation of troubles during service process
Other - EMI Module updated
Other - Preloader tools, Preloader init and other related stuff updated
Other - Scatter handling optimized for some vendor-specific stuff
Other - Automatic backup revised (manual tuneup fix)
Other - Partial LEGACY NAND support (complete boot/verify) - Identify option works now on some devices

Info:
Info: Alcatel support for NEW line devices restricted by PRELOADER level ONLY! Some partitions are PROTECTED! BROM mode not supported for now ( due remote SLA )
Info: LEGACY secure flashing now pass at any base settings but IN SOME RARE CASES (like Huawei and similar) it may lead to BaseBand and other problems.
Solution - REFLASH using CORRECT DA!
Info: ARB nowdays appearing on more devices, make sure about you FLASH SAME version. (Identify ARB LOG and SW load LOG ) Not upgrade to newer ones, if need make some extend service etc. !


Credits: Many thanks to kamal_singla, gracy_elec and other our users for providing files and/or testing and for other kind help !




Download link

 

Infinity Chinese Miracle II SCR/SPD-RDA v1.04: New models and features

Supported CPU list:
Spreadtrum : SC6530, SC6531, SC6531(A/C/D)
UniSoc : SC6531E, SC6533, SC6533G
RDA Mirco : RDA8851 rev A,B,C,L,CL
RDA Micro : RDA8826

RDA Mirco RDA8851 rev A,B,C,L,CL
RDA Micro RDA8826
Spreadtrum SC6533/G :
Flashing protocol updated
BOOTROM mode support revised
Updated LOD tools ( flashing / customizing )
Repair security revised (
-> FAC area rebuild
-> 3rd item repair activated
UserCode reading activated

Spreadtrum SC6530/6531/A/C/D/E:
Revised Repair security feature
Flashing revised
-> Secure/Signed lines flashing rebuild
-> Masterimage build revised
-> Whole flash erase fixed for NOR devices
Internal loaders updated
Database revised, loaders re-marked

Spreadtrum other:
Protocol updated, stuck issues during wrong boot selection fixed
Improved Flashing procedure for SC7701/SC7702 devices
Flashing customization module revised
InternalDB/ExternalLoader detetection/selection revised






Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.06 - AutomaticBoot selection and more...

Infinity Chinese Miracle-2 MTK/Mediatek v2.06 - AutomaticBoot selection and other stuff

To use this software Smart-Card firmware version should be 0137 or higher.

Base:
Base - Secure boot - Automatic boot selection feature released
Base - Secure boot: Allow automatic detect boot configuration for SECURE enabled chips
Base - Secure boot: Following secure configurations are supported: SBC, SLA, SDA and their combinations
Base - Secure boot: Following secure configurations are NOT supported: ARB and combinations with it
Base - Secure boot: Supported CPU: MT6572, MT6580, MT6582, MT6589, MT6592, MT6735, MT6752, MT6753, MT6755, MT6757, MT6763, MT6771, MT8127, MT8135, MT8167 ( list of tested )

Base - ModelBD - Manual Model DB update feature released
Base - ModelBD: Allow save boot configuration in sw database for future use

Base - ModelBD - Automatic Model DB update feature released
Base - ModelBD: Allow save boot configuration in sw database for future use ( press and hold LCTRL key during press IDENTIFY )

Base - FlashLoader line v1904 tested and supported. Older lines (6592/6595 and similar) still unstable
Base - FlashLoader line v1912 tested and supported. Older lines (6592/6595 and similar) still unstable

FWFlasher:
FWFlasher - Flash core updated
FWFlasher - SecureFlash on Legacy phones revised
FWFlasher - MT6771/6765 support revised

FWReader:
FWReader - More types supported for safe read
FWReader - Info reading improved
FWReader - packing revised
FWReader - more accurate data verification

Service:
Service - Format FS revised
Service - NVRAM module updated

Platform:
Platform - MT6765/MT6762 support optimized

Loaders:
LoaderDB - Lot of new agents included (Tecno, Tesla, Wiko and other)
LoaderDB - Included MT6570 "DRAM Fixed" agents used to revive devices flashed with wrong preloader ( so called "Doogee X10 bug" )

Other:
Other - Many different small changes and fixes
Other - SaveUser Configuration option can be found in FILE system menu. Work only in MANUAL mode !
Other - ErrorHandling updated - more detailed hints/explanation of troubles during service process
Other - Preloader tools, Preloader init and other related stuff updated
Other - Partial LEGACY NAND support - optimized boot. Identify work complete if BMT autoset work correct

Info: Automatic Boot option can be switched off/on in settings menu
Info: Automatic Boot work in "SelfLearning" mode - once learned it will boot this type/device line after automatically
Info: Automatic Boot option support and learn different modes ! Make sure if device used DIFFERENT settings - learn all of them !
Info: MT6570 Fixed NAND DA can be used for flashing FACTORY firmware and INIT PRELOADER. For FW read and all other things - use INFINITY ones !

How to use AutomaticBoot select, User DB, Auto DB


Download link

 

Infinity Chinese Miracle-2 SPD/UniSoc - CM2SP2 - v2.00 r1 released

Infinity Chinese Miracle-2 SPD/UniSoc - CM2SP2 - v2.00 r1 released

- Supported platforms:
SpreadTrum:
SC5735
SC7715
SC7731C, SC7731G
SC9820
SC9832A
SC9850
SC9853i

UniSoC:
SC9820E
SC7731E
SC9832E
SC9850K
SC9850KH
SC9863

- Support Generic (Non-Secure), SecureV1, SecureV2 devices
Android 4/5/6/7/8 versions

- Supported operations in initial release:
Identify ( include complete device info )
Reset Settings / Format FS
Reset FRP
Firmware flashing ( Safe Flash, Repartition, HW verify, Flash customizing )

- Database:
Basic wide-range bootloaders for common devices types
Also lot of other pre-defined models already included in database

- Extra:
Feature: Completely safe flash engine ( allow flash SimLock / Signed / and other devices, recover critical data from semi-damaged NV )
Feature: Automatic ModelDB update at new model detection ( loader select, pac load etc. )
Feature: Customized boot option and sources: Manual PAC, Manual FDL pair with automatic details detection, Pre-defined DB, Self-Learning DB
Feature: Complete Firmware Info detection at FW load with extended info




Download link

 

Infinity-Box [BEST] NK2 v1.17 - All New and Old HMD support activated

HMD N 1 **
TA-1060, TA-1056, TA-1047, TA-1079, TA-1066

HMD N 1 Plus **
TA-1130, TA-1123, TA-1111, TA-1127

HMD N 2 *
TA-1035, A-1029, TA-1023, TA-1011, TA-1007

HMD N 2.1 *
TA-1086, TA-1084, TA-1092, TA-1093, TA-1080

HMD N 2.2 **
TA-1183, TA-1184, TA-1188

HMD N 3 **
TA-1028, TA-1038, TA-1032, TA-1020

HMD N 3.1 **
TA-1074, A-1070, TA-1063, TA-1057, TA-1049

HMD N 3.1 Plus **
TA-1125, TA-1124, TA-1118, TA-1117, TA-1115, TA-1113, TA-1104

HMD N 3.2 *
TA-1154, TA-1156, TA-1159, TA-1161, TA-1164

HMD N 4.2 *
TA-1133, TA-1149, TA-1150, TA-1152, TA-1157

HMD N 5 *
TA-1044, TA-1027, TA-1024, TA-1053

HMD N 5.1 **
TA-1088, TA-1081, TA-1075, TA-1061

HMD N 5.1 Plus **
TA-1120, TA-1112, TA-1108, TA-1105, TA-1102

HMD N 6 *
TA-1033, TA-1039, TA-1025, TA-1021, TA-1000, TA-1003

HMD N 6.1 *
TA-1043, TA-1016, TA-1045, TA-1050, TA-1054, TA-1068, TA-1089

HMD N 6.1 Plus *
TA-1116, TA-1103, TA-1083

HMD N 7 *
TA-1041

HMD N 7.1 *
TA-1100, TA-1096, TA-1095, TA-1085

HMD N 7 Plus *
TA-1062, TA-1062, TA-1055, TA-1046

HMD N 8 *
TA-1012, TA-1004, TA-1052

HMD N 8.1 *
TA-1128, TA-1121, TA-1119

HMD N 8 Sirocco *
TA-1042, TA-1005

HMD N 9 PureView *
TA-1094, TA-1087, TA-1082

HMD N X71 *
TA-1172


For now the next features are supported:
> Firmware flashing ( Factory / BEST firmware packages )
> Format FS / Reset Settings
> Reset FRP
> Identify

Info marks:
* - Device require Remote Authentification Server ( credit cost - 0 for now )
** - Device supported / supported already STANDALONE

- Base
Support for old HMD line over RAS for QCOM models
Support for new HMD line - WT/HQ activated - 2.2, 3.2, 4.2 ( over RAS for QCOM models )
Loader database updated
ModelFinder updated
FileSystem toolkit updated, changed FormatFS for all SP lines
SW/HW/Cross-avoid check activated for BL update mode
Bugfixes and minor changes

- MTK SP
Updated loader database
Boot log now show also ARB state and other service info
Automatic backup for critical partitions activated

- MTK FP
SWVersion check revised
FlashEngine updated
FileSystem (Forensic) engine updated

- SPD FP
Backup / Restore security activated
FlashEngine revised

- Support
Some firmwares for wide range of QCOM/MTK HMD Smartphones can be found on support area



Infinity-Box [BEST] NK2 v1.18 - important fix for v1.17

You can download complete v1.18 package as well as v1.18-exe-only if you have v1.17 installed

- Base
Flash engine revised ( N 2/2.1/5/6 flashing fixed )
Format FS / FRP reset revised

Other minor changes and fixed


Complete package v1.18: Download link #1 - Download link #2 - Download link #3


You can download small package v1.18 exe-only if you have v1.17 already installed.

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.06 - AutomaticBoot selection and more...

Infinity Chinese Miracle-2 MTK/Mediatek v2.06 - AutomaticBoot selection and other stuff

To use this software Smart-Card firmware version should be 0137 or higher.

Base:
Base - Secure boot - Automatic boot selection feature released
Base - Secure boot: Allow automatic detect boot configuration for SECURE enabled chips
Base - Secure boot: Following secure configurations are supported: SBC, SLA, SDA and their combinations
Base - Secure boot: Following secure configurations are NOT supported: ARB and combinations with it
Base - Secure boot: Supported CPU: MT6572, MT6580, MT6582, MT6589, MT6592, MT6735, MT6752, MT6753, MT6755, MT6757, MT6763, MT6771, MT8127, MT8135, MT8167 ( list of tested )

Base - ModelBD - Manual Model DB update feature released
Base - ModelBD: Allow save boot configuration in sw database for future use

Base - ModelBD - Automatic Model DB update feature released
Base - ModelBD: Allow save boot configuration in sw database for future use ( press and hold LCTRL key during press IDENTIFY )

Base - FlashLoader line v1904 tested and supported. Older lines (6592/6595 and similar) still unstable
Base - FlashLoader line v1912 tested and supported. Older lines (6592/6595 and similar) still unstable

FWFlasher:
FWFlasher - Flash core updated
FWFlasher - SecureFlash on Legacy phones revised
FWFlasher - MT6771/6765 support revised

FWReader:
FWReader - More types supported for safe read
FWReader - Info reading improved
FWReader - packing revised
FWReader - more accurate data verification

Service:
Service - Format FS revised
Service - NVRAM module updated

Platform:
Platform - MT6765/MT6762 support optimized

Loaders:
LoaderDB - Lot of new agents included (Tecno, Tesla, Wiko and other)
LoaderDB - Included MT6570 "DRAM Fixed" agents used to revive devices flashed with wrong preloader ( so called "Doogee X10 bug" )

Other:
Other - Many different small changes and fixes
Other - SaveUser Configuration option can be found in FILE system menu. Work only in MANUAL mode !
Other - ErrorHandling updated - more detailed hints/explanation of troubles during service process
Other - Preloader tools, Preloader init and other related stuff updated
Other - Partial LEGACY NAND support - optimized boot. Identify work complete if BMT autoset work correct

Info: Automatic Boot option can be switched off/on in settings menu
Info: Automatic Boot work in "SelfLearning" mode - once learned it will boot this type/device line after automatically
Info: Automatic Boot option support and learn different modes ! Make sure if device used DIFFERENT settings - learn all of them !
Info: MT6570 Fixed NAND DA can be used for flashing FACTORY firmware and INIT PRELOADER. For FW read and all other things - use INFINITY ones !

How to use AutomaticBoot select, User DB, Auto DB


Download link #1

Download link #2

Download link #3

Download link #4

 

Infinity Chinese Miracle-2 SPD/UniSoc v2.01 - UniReader Edition - Android 4-5-6-7-8-9

Infinity Chinese Miracle-2 SPD/UniSoc v2.01 - UniReader Edition - Android 4-5-6-7-8-9

As ordinary, Infintiy Team continue to release unique and world-first software features, algorithms and methods.

- Core
Protocol updated
Alternate protocol support activated ( automatic switch depends on model )

- New Self-Learning engine for semi-supported devices !
In case of problem with device servicing - during identify session SW will make new database record
That record available from boot menu after that to use exactly for this device line
That will fix any incompatibility loader <-> device problems and remove any servicing issues

- Service
Identify - better structure detection, simlock state info
Identify - Userdata state detection optimized
Format FS - Forced Format revised

- Flasher
Optimized PAC handling
Optimized older device line support ( Sc7715-Sc9832 from SPRD )
NVManager updated - Identify, Security swap and verification, Recovery mode
Activated flashing of own FlashFile format files made by FWReader

- Firmware Reader activated!
Allow read ANY security level phone from Spreadtrum or UniSoc on almost all Android OS versions!

Support OLD SPRD line devices:
SC7715, SC7731, SC9820, SC9832, SC9850 and their revisions and modifications
Plain, Signed and RSA-enabled
Android 4, Android 5, Android 6, Android 7 lines are supported (higher versions were NOT released from SPRD)

Support NEW UniSoc line devices:
SC7731E,SC9832E,SC9863,SC9850,SC9820E and their revisions and modifications
Plain, Signed and RSA-enabled
Android 6, Android 7, Android 8, Android 9 lines are supported (lower versions were NOT released from UniSoc)
Arch32/Arch64 support

Support "SPRD"-like chipsets with Intel X86 arch
SC9853I and its modifications and revisions
Plain, Signed and RSA-enabled
Android 6, Android 7, Android 8 lines are supported

It is the only existing and complete solution

Additional info:
Firmware use OWN format.
Firmware is COMPLETE one, allow to fix any sw-related state including FlashChip erase, change or complete SW rebuild
Unlike older SWReader version used in V1 line there is no need in bunch of additional re-connection operations or to make something special.

- Database:
New generic boots included, some boots updated

- Other
Bug fixes and some changes according users requests

- Known issues:
[1] UniSoc line is SLOW. It is VERY SLOW! Unlike SPRD ones, it consume x4-x5-x6 more time comparing to old SPRD.
We made almost all possible for now to speed it up. And that is limit for protocol.
In near time it should be some speed up to 20-30% but this solution still require some more time.
[2] UniSoc devices with ARB active may dead on wrong SW version flashing at Android 9 line.
We checking that issue and collecting samples. According users test and reports solution will follow.
[3] Some old devices after FW flashing may gone to "Encryption Unsuccessfull" state, right now - "ResetPhone" button enough.
[4] Sw will try always, in any case retrieve all device-side keys/security during flashing and identify, if they exists inside.
Much backups better, that nothing. Actual for devices with paired/signed security and/or active keybox.
[5] NAND devices on SC9820,SC7715,SC8830 not supported yet for FW reading


Discussion and download links are HERE

 

Infinity Chinese Miracle II SCR/SPD-RDA v1.05 - New models and features

Infinity Chinese Miracle II SCR/SPD-RDA v1.05 - New models and features



As ordinary, Infintiy Team continue to release unique and world-first software features, algorithms and methods.


Supported CPU list:

Spreadtrum: SC6530, SC6531, SC6531(A/C/D)
UniSoc: SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826

RDA Mirco RDA8851 rev A,B,C,L,CL
RDA Micro RDA8826
Spreadtrum SC6533/G:

Updated LOD tools ( Factory LOD support revised )
UserCode reading improved

Spreadtrum/UniSoc SC6530/6531/A/C/D/E:

New feature activated: Complete identification
During Binary Dump selection SW will extract complete device info ( build version, time, HW details etc. )
During PAC file selection SW will extract complete device info ( build version, time, HW details etc. )
During Flash Reading SW will extract complete device info ( build version, time, HW details etc. )
Readout naming changed to DeviceInfo details instead of flash size/flash vendor

Repair security revised
Database revised, loaders updated ( extended range of supported SC6531EFM devices with 4-8MB flash )

Spreadtrum/UniSoc other:
Protocol updated, error codes handling activated
SC6531 with 16MB flash support revised
FTM during flashing now make DNVM clean, FS clean and structure verification
UserCode reading improved
Some other bugfixes and small changes

Info:
"HardLock" detection feature for SP-locked device activated under test

We are looking for SP-locked samples RDA Micro / UniSoc / SPDR FP platforms. Please contact to rd [at] infinity-box.com if you have units for test on hands.




Password for archive file (if any) is: 12345678


Download link #1
Download link #2

 

Infinity Chinese Miracle-2 SPD/UniSoc v2.02 - Android9, Privacy, New models and more

Infinity Chinese Miracle-2 SPD/UniSoc v2.02 - Android9, Privacy, New models and features

As ordinary, Infintiy Team continue to release unique and world-first software features, algorithms and methods.

- Core
Protocol updated
Error handling, error explanation and hint module activated
SC9850 and similar devices WRITEFLASH security disable option enabled
> Use for custom / forced / service operation on secure-enabled SC9850 phones (in case of "AC SECURITY" error)

- Android 9 line devices tested and supported for Firmware reading!
- Self-Learning mode for Firmware Reader activated!
That feature allow analyze new and unknown devices "on the fly" and make complete and correct firmware
Just follow the SW instructions if need and you don't need to wait updates for latest devices

- Service
Security - NVM reading feature activated
> Allow read complete device factory calibration data, security items
> Save also modem info for cross-writing NV between different models
Security - NVM writing feature activated
> Allow restore / rewrite device factory calibration data, security items
> Allow use different modes during restore:
> 1. SWAP ( safe mode ) - if security alive SW will try swap security data
> 2. Complete restore ( rebuild mode ) - destroy ALL original security data if it was inside phone
Identify - better structure detection
Identify - BaseBand deep identification
> Allow read complete BaseBand info and read "MODEM TAG"
> Since nowdays there much SAME devices under DIFFERENT names but same by RADIO part - you may use NVM according that TAG
> TAG now saved during NVM read operation, you can use default Windows search bar in Backup folder to seek need TAG
UserData - PrivacyLock read feature activated
> Allow read PRIVACY lock password and details
> Support DIFFERENT models made by OEM "TRANSSION"

- Flasher
Optimized speed ( from 5% to 15% for UniSoc line )
Optimized PAC handling
Optimized older device line support ( SC7731GEA and similar from SPRD )
NVManager updated - Identify, Backup, Security swap, Verification
Activated new option - Re-Sparse.
> Allow prepare big filesystem images before flash. Useful for low-ram devices and adnroid 9 devices
> Use that option, if have face "INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!" error during SYSTEM flashing

- Firmware Reader
Android 9 line support finished, completely tested and confirmead as working
Vendor-specific mode activated. SW will identify "non-standard" devices and make firmware complete and correct now
> FOTA, vendor-specific features and rest stuff has been tested

- Database:
New generic boots included for SC7731C/G
New generic boots included for SC9863
ZTE lines devices included - A5(2019), A7(2019), L130, L8 and some others

- Other
Bug fixes and some changes according users requests

- Known issues :
[1] UniSoc line is SLOW. It is VERY SLOW! It may takes up to 3-4 times more time comparing with old SPRD.
[2] UniSoc devices with ARB active may dbe ead on wrong SW version flashing at Android 9 line.
We are checking that issue and collecting samples. According to users test and reports solution will follow.
[3] Some old devices after FW flashing may gone to "Encryption Unsuccessfull" state, right now - "ResetPhone" button enough.
[4] UniProt option active may lead to FLASHING problems on old SC7715-SC7731 line devices. Disable this option if you have a problem with old SPRD
[5] NAND devices on SC9820, SC7715, SC8830 are not supported yet for FW reading


Download link #1

Download link #2

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a separate product, this means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but nmot only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.




Download link

 

Infinity Chinese Miracle-2 SPD/UniSoc v2.03 - Easy Identify, New models & features

Infinity Chinese Miracle-2 SPD/UniSoc v2.03 - Easy Identify, New models & features

As ordinary, Infintiy Team continue to release unique and world-first software features, algorithms and methods.

- Core
Protocol updated
Error handling, error explanation and hint module updated

- Service
NVM operations revized
DiagMode option activated ( Platform -> Control -> DiagMode )
> Change SW mode to diag, instead of flash. Do not require BootSelection.
Allow for now:
1. Identify Device - ModemInfo, Build Info, SecurityInfo, SOC Info, DeviceHW Info
2. Format FS / Reset settings ( NOT touch FRP! ) - WIPE mode
3. Read NV data, verify NV
> Don't forget change SW mode between Service/Flash for those operations !

New Identify option - device Platform, Device HW details identification
> Allow detect device SOC family, RAM amount for faster loader selection
> Work in DiagMode, Work ON MODERN and UNISOC chipset only !

- Flasher
Optimized flashing protocol
Optimized older device line support
NVManager updated - Identify, Backup, Security swap
NVManager Recovery tool updated

- Firmware Reader
Optimized structure identification
Activated "forced" reading. Option skip data verification.
> In case of semi-damaged devices, if backup atleast of something required
> In case of "Critical data damaged" errors
Optimized data verification during create FW

- Database:
SC983xx generic loader DB updated
SC9853i generic loader DB updated
SC7731E generic loader DB updated
SC7731x generic loader DB updated
SC9863 loaders DB updated - BQ, Wiko, ZTE, Symphony
SC7731c/g loaders DB updated - various models and RAM size
SC9832E loaders DB updated - Meizu, Wiko
Some other various models with specific hw settings included in loader DB

- Other
Boot Selection mode are indepedent ( loader base can be changed after FW selection, in Platform tab )
Bug fixes and changes according users requests

- Special thanks to respected Mr. gracy_elec


Download link

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a separate product, this means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but nmot only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.




Download link

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a completely new separate and independent product that has no any relation with previous projects.
This means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but not only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.


Video tutorial Arabic:




Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.07 - New models and features

Infinity Chinese Miracle-2 MTK/Mediatek v2.07 - New models and features

As you know Infinty Team work hard and silently, but results of silent work may exceed any expectation.
It takes more that hour to prepare list of changes so you can imagine how much time takes a work itself.
Let's respect silent hard work instead of everyday's bla-bla (like many others do).

Thank you to be with us during last 15 years !

List of changes for v2.07:

Core:

NewSOC : MT6785 support under test
NewSOC : MT6885 support under test
Changed : Protocol updated for RAPHAEL line
Changed : Protocol updated for LEGACY line
BugFix : MT6752 support fixed
BugFix : MT8172/MT8173/MT8176 BROM support fixed
BugFix : MT6570 support fixed
Changed : EMI engine revised
Changed : AutomaticBoot selection revised. More types and combinations are supported.
Changed : Loader v1924 supported and tested
Changed : Loader v1936 supported and tested
Changed : Loader v1944 supported and tested

Flasher :
New feature: unmerged signature support
- Files with external signatures now flash correctly
New feature: Forced mode for Raphael line
- Allow automatically skip repartition, erase operations if it was not allowed without break flashing
New feature: WHOLE Flash Pre-Erase
- Erase whole USER region. Destroy ALL data include unique and secure one! Support both Modern and Legacy lines.
Changed: Repartition procedure rebuild to support modern devices and special cases (user memory issues and other fixes)
New feature: Smart erase
- In manual mode selection and enabled pre-erase all unchecked partitions will not be touched
- Storage boundary checks now works correct on legacy and modern lines

Firmware Reader / Maker:
Changed: Local DB updated to latest version
Changed: Scatter creation support latest platforms and variants
Changed: Scatter compatibility with SPFT optimized ( for DL only mode )
New feature: FileSystem creation and params now generated according Android version
New feature: Ability to skip "critical" partitions verification during read ( bl-unlocked devices and specific cases )

MemoryTool:
New feature: Switch working mode ( ADR - PRT options in global settings ) without tool restart (no need to exit and run software again)
New feature: Error ignoring on RAPHAEL line devices. Errors are not triggers shutdown anymore.
Changed: Update PMT operation rebuild. Support modern devices and use multiple factors now.
Changed: Init preloader operation. Support plain preloader dumps that was created by MemoryTool.
Changed: Partition listing style on LEGACY devices. In case of protected regions do not triggered shutdown anymore.
Changed: Write operation now handle correctly some sparse images used in Android 9 and newer versions

Service:
BugFix: Format FS procedure updated
BugFix: Reset FRP procedure updated
BugFix: Identify procedure updated and revised
New feature: eMMC life counter check during Identify
- Show, if possible by Agent or HW, storage life status. LifeCycleEnd(ReadOnly), LifeCycleNearEnd states.
- Support only Raphael newer than MT6739. Support NAND devices as well ( MT6570 )

UserData:
New feature: Reset Privacy Locks
- Support old and modern devices. Procedure is USERDATA SAFE if that required

LoaderDatabase:
Base Loader v1924 included
Base Loader v1936 included
Base Loader v1944 included
New TECNO sec agents included
New VIVO sec agents included
New ALCATEL sec agents included
New Hisense sec agents included
New Moto sec agents included
New Huawei sec agents included
New Lenovo agents included
And other different and generic models can be found in list

Other:
Changed: Base DB revised, unused and "buggy" types removed from BASE agents.
- Change settings if DA version not contain your device platform
Changed: EMIDb updated, more types supported
Changed: Preloader parser now shows more complete memory details

Thanks to:
Special thanks to respected Mr. gracy_elec
Special thanks to respected Mr. Kamal_singla


Download link #1
Download link #2
Download link #3

Password for archive is: 12345678

 

Infinity Data Explorer v1.03 - RDA based firmware images are supported and more

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a completely new separate and independent product that has no any relation with previous projects.
This means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but not only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.


Video tutorial Arabic:




Download link

 

Infinity Chinese Miracle-2 SPD/UniSoc v2.04 - Xiaomi, KaiOs, RepairSec, PACv2 & more

Infinity Chinese Miracle-2 SPD/UniSoc v2.04 - Xiaomi, KaiOs, RepairSec, PACv2 and more

Silent work is much better than thousand words...

- Support for PACv2 format activated
- Core updated
- Protocol updated
- SC9820E support activated ( Generic and Secure types )

- Repair security option activated
Allow repair device security items on generic devices
Work in Flash mode
Work in DiagChan mode
SimLock-enabled devices may NOT work
Security-enabled devices will NOT work

- Firmware Flasher updated
Updated core
Updated PAC types support
Revised NVManager

- Firmware Reader updated
More accurate data verification
Reading speed optimized for some UniSoc models
Android version-depend mode activated ( allow avoid flashing issues on android 9 and newer )
KaiOS devices supported ( SC7731E eMMC, SC9820E eMMC tested and working ) now for Read Firmware

- Identify procedure revised
Now it also support for security verification ( signed NV )
Better FS state verification
More usable build props info extraction

- Revised manual mode selection and possible combinations ( can combine firmware and loader from any source )

- Loader database
SC7715 eMMC loaders included
SC9820 loaders updated
SC9863 loaders updated
SC9820E eMMC loaders included
Various range of models from Wiko, LYF, BLU, BQ, Symphny, Itel and others included in DB

- Other
Bug fixes and changes according users requests

- Extra
Xiaomi QIN 1S+ supported ( Identify, Repair, Firmware Reading, Reset Settings ) BKey : Call button
Xiaomi QIN 2 supported ( Identify, Firmware Flash, Repair, Firmware Reading, FRP, Reset Settings ) Bkey : Assistant button
Xiaomi QIN 2 Pro supported ( Identify, Firmware Flash, Repair, Firmware Reading, FRP, Reset Settings ) Bkey : Assistant button

Special thanks to respected Mr. gracy_elec !


Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.08 - New models and repair features

As ordinary, uniques functions and methods released.

Please do not forget to download new drivers v5.1632_x86_x64 !

Core:
Changed : Loader v1952 supported and tested
BugFix : Rebuild support for MT6572 line ( KaiOs and old devices )
Changed : Automatic selection of higher available BASE loader at startup
Changed : Automatic protocol switching for RAPHAEL line
Changed : Initial META protocol support
Changed : AutomaticBoot selection revised. More types and combinations are supported.
Changed : Protocol updated for RAPHAEL line

New feature : Meta protocol support activated
!*Support Legacy line ( MT6572 .. MT6595 )
!*Support Raphael line ( MT6750 .. MT6797 )
!*Support Modern Raphael line ( MT6761, MT6765 and newer )

Function : Identify ( AP/MD, SWversion info, Security details )
Function : Reset Settings / Format FS ( NOT touch FRP )
Function : Repair security for
Legacy line ( from MT6572 and up to 6580 )
Raphael line ( from MT6570 to MT6765 etc. )

!*Devices with SLA will not work for repair without auth! ( even if Meta started )
!*Devices with OTP will not work for repair! ( SW will just show write error )

Service:
Changed : Format FS procedure updated
BugFix : Identify procedure updated and revised
Changed : eMMC life counter check ( Raphael, more accurate status handling for latest loaders )

UserData:
Changed : Reset Privacy Locks procedure updated

MemoryTool:
BugFix : Long-run reading optimized for RAPHAEL line

Firmware reader:
Changed : Updated support for legacy platforms
Changed : Updated support for MT6739 FP-like and KaiOS phones
Changed : Local database update
Changed : Data verification improved
Changed : More types supported

Flasher:
BugFix : In some cases were made wrong SV5_BL image selection for EMI base
Changed : Protocol updated for RAPHAEL line
Changed : Protocol update for LEGACY line
BugFix : Flash Erase ( whole mode ) revised
BugFix : Flash Pre-Erase ( safe upgrade mode ) revised

Other:
Changed : Boot helper updated. Take attention to software logs and follow them. In most cases that enough to setup correct settings
New feature : Reboot option activated in main tab. Switch charge / power off mode after operations
New feature : META switch option activated in main tab. Used to switch SW between FLASH and META mode
Changed : Loader database updated
Changed : Minor changes in GUI, check buttons/fields hints to know more about alternative modes and special options of supported functions

Info:
META require working device condition. Charged battery (more than 20%). Installed drivers.
New drivers v5.1632_x86_x64 is at support area.


Password for files: 12345678


Drivers


Download link #1

Download link #2

Download link #3

Download link #4

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.09 - SP-unlock for modern platforms + more

As ordinary, uniques functions and methods released

The only words I can say are HERE

Core
BugFix : SelfLearning ( Automatic Boot Selection ) feature updated
!*In some cases may require repeat learning for some platforms

New Feature : Enter META from BROM mode
!*Support LEGACY legacy
!*Support RAPHAEL line
!*In case of secure fuse, auth can be used ( setup in model selection, or manual select as AUTH file )
!*May not work in TestPoint cases on some platforms

Service
Changed : Repair security procedure updated (Flash and Meta mode)
Changed : SPUnlock procedure updated (Flash and Meta mode)
Changed : Unlock in Meta mode activated for modern platforms ( MT6739 and newer )
Changed : Identify procedure updated

Firmware Reader
Changed : Improved structure identification
Changed : Support more different types
BugFix : Fixed some old platforms support

MemoryTool
Changed : Path Selection now automatically select files in WRITE FILE fields if they are exists in selected folder

Flasher
BugFix : Fixed flashing for old slow platforms ( MT6735 / MT6580 )

Meta protocol functions updated
Changed : Identify now read all Android info, like in FlashMode
!*Feature will not work on old devices ( Android 4.x, MT6572 and similar legacy chip typess )
Changed : Updated security detection feature
BugFix : Updated different Legacy and Modern platforms support
Modem warmup not cause fatal errors on some old phones
Modem-less devices detection ( wifi tablet / smartwatches )
Changed : Format FS revised
*!Some models can not be reset with that feature ( found in some Oppo )
BugFix : Updated structure verification
Changed : Repair Security rebuild, support more types and non-standard cases

New Feature : SP Unlock
Tested and confirmed as working in LEGACY line ( Teseted with MT6735, MT6580, MT6752, MT6753. Should works on other legacy chip types )
Tested and confirmed as working in RAPHAEL line ( Teseted with MT6739, MT6761, MT6755, MT6750. Should works on other Raphael chip types )
We are looking for user reports and interest test cases

Other
BugFix : Some minor changes and bugfixes


Password for files: 12345678


Download link #1

Download link #2

Download link #3

Download link #4

Download link #5

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a completely new separate and independent product that has no any relation with previous projects.
This means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but not only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.


Video tutorial Arabic:




Download link

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a completely new separate and independent product that has no any relation with previous projects.
This means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but not only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.


Video tutorial Arabic:




Download link

 

Infinity Chinese Miracle II SCR/SPD-RDA v1.06 - New models and features

Infinity Chinese Miracle II SCR/SPD-RDA v1.06 - New models and features

As ordinary, Infintiy Team continue to release unique and world-first software features, algorithms and methods.

Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C/D)
SpreadTrum: SC68xx ( with external PAC )
SpreadTrum: SC7702 ( with external PAC )
UniSoc: SC6531E, SC6533, SC6533G, SC7702
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826

Core
NewChip: Support UNISOC 8910 (FLASH) under test
NewChip: Support IVY IoT (FLASH/SVC) under test
Changed: UpToDate Protocol changes for latest FP platforms ( UniSoc )
BugFix: Connection on SPRD tab
BugFix: BOOTROM mode on latest SC6533G branches

Support UNISOC 8910DM / UIS8910 chipset ( SVC mode )
- Identify ( Security info, compilation info, modem info , APinfo )
- Format FS / Reset Settings
- Read UserCode / PrivacyCode
- Repair Security
!* Generic types only

New Feature: SVC ( Diag ) mode support for SPRD / UniSoc
- Identify ( Security info, compilation info, modem info )
- Format FS / Reset Settings
- Read UserCode / PrivacyCode
- Repair Security
!* Generic types only

Service
BugFix: Security repair not allow use some "non-standard" combinations ( RDA / SPRD / UniSoc )
Changed: CompileInfo extraction improved ( RDA / SPRD / UniSoc )
Changed: GUI revised for repair part ( CS info, Automatic complete at double click for security fields )

UserData
BugFix: Security code read in FlashMode revised ( SPRD )

Other
BugFix: Lot of small different changes and fixes






Download link

 

Infinity Chinese Miracle-2 SPD/UniSOC v2.05 - NAND, KaiOs and new features

Infinity Chinese Miracle-2 SPD/UniSOC v2.05 - NAND, KaiOs and new features

As ordinary, unique functions and methods released

Core
NewChip : SC7731E with NAND ( KaiOS and MocorDroid5 )
NewChip : SC7715x with NAND ( KaiOS , MocorDroid5 , Android 4x)
NewChip : SC9820x with NAND ( MocorDroid5 , Android 4x)
Protocol : Speed increased for most operations ( SPD and UniSOC )
Protocol : Protocol changes according SPD/UniSOC R23 line

New Feature : NAND support ( SPD and UniSOC generation )
!* Support flashing Factory / InfinityFW
!* Support correct flash selection and servicing phones with NAND
!* Support InfinityFW reading ( Complete, Factory-Like )
!* Support Service operations

Service
Changed : Repair security procedure updated (Flash and Diag mode)
Changed : Identify procedure updated
!* Support complete and fast NAND devices identification
!* Support complete simlock info structure identify and verify
!* Support multi-nv structure detection and security info detection
!* Database update / self-learning updated
!* FileSystem identification support UBIFS and F2FS detection
Changed : Format FS / Reset FRP procedure updated

Firmware Reader
New Feature : NAND support
!* Support old and new generations ( SPD and UniSOC )
!* Support plain Android , KaiOs and MocorDroid5 OS
!* Automatic and correct FileSystem creation for NAND devices
!* Support all security types, include UniSoc secure/signed
!* Produced FW is 100% like factory one
Changed : FileSystem creation engine updated ( UBIFS support , bugfixes )
Changed : Improved structure identification
Changed : Support more different types
Changed : Old SPD line support rebuild ( SC7715,SC7731,SC983x,SC9820x )
Changed : Fixed FW creation in full manual / skip verify mode settings

Flasher
New Feature : Complete flash erase ( whole flash format ) during flashing ( eMMC / NAND )
New Feature : Correct NAND flashing support ( SPD and UniSOC ) ( Factory PAC and InfinityFW )
Changed : Flashing core for InfinityFW more stable

Loader Database
NewChip : SC7715 BASE NAND revisions included
NewChip : SC9820 BASE NAND revisions included
NewChip : SC7731E BASE NAND revisions included
NewChip : SC7731E BASE eMMC LOW_MEM revisions included ( cheap A8-A9 devices )
NewChip : SC7731x BASE eMMC LOW_MEM revisions included ( old A4-A5 GEA devices )

Other
Changed : Manual mode : automatic structure and setting detection in manual mode
Changed : Automatic base settings selection for BASE loaders ( Protocol, Charging, FlashSettings )
Changed : Separate NAND mode option activated in platform settings for manual mode
BugFix : Lot of minor changes and bugfixes
Changed : Software compatibility with other applications improved


Download link #1

Download link #2

Download link #3

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.10 - New MTK chips and UFS storage

​

Infinity Chinese Miracle-2 MTK/Mediatek v2.10 - New MTK chips and UFS storage

As ordinary, unique functions and methods released

Core
NewChip: Helio G90T (Formely MT6785) supported (UFS / eMMC)
NewChip: MT6731 supported (eMMC / NAND)
NewChip: Helio A20 (Formely MT6761 low-cost revision) supported
NewChip: Helio P90 (Formely MT6779) support under test (UFS / eMMC)
BugFix : MT6595/MT6597 BROM support broken, fixed (Agent 17xx-19xx)

New Feature : UFS FlashIC support
!* Support flashing Factory / Infinity FW
!* Support MemoryTool
!* Support Factory Firmware reading
!* Support Service operations
!* SOC's on market, support UFS chips right now : G90, P70, P90

Service
Changed : Repair security procedure updated (Flash and Meta mode)
Changed : SPUnlock procedure updated (Flash and Meta mode)
Changed : Identify procedure updated
Changed : Format FS / Reset FRP now support UFS flash too
New Feature : Modem Re-Init (NVfix)
!* Useful after FixBB, in case of modem subsystem alive

Firmware Reader
New Feature : UFS flash support
New Feature : Combo scatter creation for newest chipset
!* Produced scatter MAY NOT work with OLDER SPFT (factory flasher) below 19xx versions!
!* Produced scatter is 100% like factory ones
Changed : Improved structure identification
Changed : Support more different types
Changed : NAND support revised
Changed : LEGACY line support revised
Changed : Platform and version depend scatter creation for better compatibility with SPFT
Changed : LEGACY line with Android 9 (MT6580 and similar) specific changes

MemoryTool
New Feature : UFS flash support
!* Support Read , Write , Erase partitions
!* Support RePartition
!* Support Preloader init
!* Support Change Work mode (ADR / PRT)
!* Change storage settings useless, all flash content mapped in single mode
Changed : Structure identification
Changed : Automatic files selection at folder change

Flasher
New Feature : Support COMBO scatter's (v2.xxx)
!* Automatic selection depend on device Flash (UFS/EMMC/NAND)
!* Storage selection done automatic according detected, for end-user all selection and rest settings remain same as before
New Feature : Support MTK chips with UFS FlashIC flashing
!* All features (Erase / Verify / PMT upgrade / Backup / HW Compatibility) work for devices with UFS as well
Changed : Scatter tab changes, specific to multi-storage selection and settings

Meta protocol functions updated
Changed : Updated security detection feature
BugFix : Updated structure verification

Other
BugFix : A lot of minor changes and bugfixes applied
Changed: Many internal changes to improve compatibility with other applications, antiviruses and similar software.
Changed: Software load/operation speed improvements implemented




Discussion and download links are HERE

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.11 - New features activated

Read about CM2MT2 v2.10 Infinity Chinese Miracle-2 MTK/Mediatek v2.10 - New MTK chips and UFS storage because v2.10 has major improvements and v2.11 is a successor of v2.10 with new improvements and fixes !


Core
BugFix : META protocol updated
Changed : Loader v2012 supported and tested

Service
Changed : Identify in META now read NVRAM dump that is compatible with flash mode writing
!*Feature may not work on old devices - Android 4.x, MT6572 and similar legacy chips
!*Feature useful also for devices which can not connect via flash mode as security save way

Changed : Identify now also verify EXTRA security flags
!*Signed types detection ( RSA signed security items )
!*Encrypted types detection ( Vendor-modified security items )
!*Edit/Repair security on those types IS NOT possible at the moment !
!*Swap security on those types IS NOT possible at the moment !

New Feature : Google Attestation key installation
!*Allow upload attestation keys to devices which require it ( Google Key red mark in phone after complete boot )
!*In most cases it model-depend file!
!*SW DO NOT allow select wrong file ( non attestation-key file ) by verify content of file
!*Files in most cases delivered with factory fw package ( kb.bin , Android_Key and other similar )

Firmware Reader
Changed : Improved structure identification
Changed : Support more different types

Flasher
Changed : File selection optimized for latest build revisions - multi-bundle etc.

MemoryTool
Changed : Init PMT procedure updated (NAND, EMMC, UFS)
Changed : Init Preloader procedure updated (NAND, EMMC, UFS)

Other
BugFix : Minor changes and bugfixes
BugFix : Compatiblity issues fixes


Password for files: 12345678


Download link #1

Download link #2

Download link #3

 

Infinity Chinese Miracle-2 RKT/Rockchip v2.02 - New chips and latest Android support

As ordinary, unique functions and methods released


Core
BugFix : Connection stack updated
BugFix : Compatibility with latest drivers releases
Changed : Core rebuild for support modern SoC's and old SoC's revisions with Fuse/SecureBoot support

Support RK29xx series ( NAND )
Support RK30xx series ( NAND, eMMC )
Support RK31xx series ( NAND, eMMC )
Support RK32xx series ( NAND, eMMC )
Support RK33xx series ( NAND, eMMC )
Support RKPX5 series ( NAND, eMMC )

Service
Changed : Identify procedure rebuild. Complete info reading and parameters detection
!*If Identify CAN NOT display SWVersion details it may means device can not be serviced for FWRead operations
Changed : FRP reset revised to support latest Android versions and Modern SoCs
Changed : FS format revised to support latest Android versions and Modern SoCs

Firmware flasher
New Feature : Modern RK UnionImage flashing supported
New Feature : Combined Sparse image flashing supported
New Feature : Repartition for RK-PARA and RK-GPT supported
New Feature : Factory (UnionImage) Firmware flashing for latest Rockchip SoCs versions/revisions
Changed : Support Infinity Firmware Flashing ( Old and Modern SoCs revisions )

Firmware Reader
New Feature : Android 7 devices supported
New Feature : Android 8 devices supported
New Feature : Android 9 devices supported
Unique : Firmware read allow read FW from "unreadable" Android 8/9 devices
!*Feature support eMMC and NAND devices which can not be dumped by any tools over native protocol ( No Root / ADB need )
!*Feature support some "slow" NAND cases on modern SoC's
!*Feature may not work on some NAND devices with FTL/ECC errors and Flash Faults
Changed : Improved structure identification
Changed : Support more different types

Other
BugFix : Minor changes and bugfixes
Drivers : New driver package with Win8/Win10 x86/x84 can be found on support area
Info : SW may work not correct in some cases with RK29xx and RK31xx OLD NAND 4.x devices
Info : New driver installation is REQUIRED for correct work !


password for files: 12345678


Download link #1

Download link #2

Download link #3

 

Infinity Data Explorer software

Dear Friends,

Here is an information about Data Explorer software.
This software is a tool that helps to extract user's data from full flash file that you can read from phone with Infnity software (or other tools that can build plain bin file as output).
In this thread we will post news and information about this software functions.

This software is a completely new separate and independent product that has no any relation with previous projects.
This means you should buy an Data Explorer Activation from your seller to be able to use this software.
Data Explorer Activation available for the next Infinity Products:
- Infinity-Box/Dongle
- Infinity [BEST]
- Infinity CDMA-Tool
- Infinity Content Extractor Dongle


If you have any kind of requests about feature and supported models please post it here. We hope to get detailed technical information about features/devices but not only "need update" text.
Thank you for your kind understanding !


There is a special discount (30 IOS credits for today) for users who have bought Content Extractor software in period from 01-Jan-2014 to year 2019.
There is no any automatic discount system ready at the moment but you can post your S/N in current thread and we will return credits to your IOS account after purchase.


Video tutorial Arabic:




Download link

 

Infinity Chinese Miracle-2 MTK/Mediatek v2.12 - F2FS support, EncryptInfo and more

As ordinary, unique functions and methods released


Core
BugFix : Some legacy chips support may broken, fixed (Agent 19xx-20xx)
BugFix : BROM mode support fixed for MT6752/MT6753

Service
Changed : Identify procedure updated, read more useful info on Android 10 devices
!* From now on for modern Android ( 7 - 10 ) shown more detailed UserData state with encryption methods
!* That replace old ENCRYPTED/PLAIN states to avoid false-positive results for forensic cases
!* It may work not stable on earlier Android releases, it is recommend to check state also via MemoryTool if required
New Feature : Smart Reset ( Format FS option )
!* Support RAPHAEL line in SMART mode, not need change any options
!* Function detect correct settings automatically to avoid user from mistakes
!* Function detect correct file systems, include modern F2FS, and all variants of EXT filesystem to support wide range of old and modern devices
!* Function detect and reset all settings, include FRP and Privacy Locks ( for USER DATA SAFE methods - USE SEPARATE OPTION!!!!! )
Changed : META : Attestation Keys download procedure updated

Firmware Reader
New Feature : F2FS file system detection and creation supported
Changed : Improved structure identification
Changed : Support more different types
Changed : Combo scatter creation revised
Changed : Platform and version depend scatter creation for better compatibility with SPFT
Changed : Android version-depend additional data creation

MemoryTool
Changed : Structure identification
New Feature : Build FILE SYSTEM at selected partitions
!* Allow make F2FS, EXT4 old and EXT4 modern variant of filesystem at selected partition
!* Select need partition ( for prevent mistakes - just one partition per operation allowed ) and desired filesystem
!* Useful also in case of unlocked devices with change FS or encryption method needs

Flasher
New Feature : Android 10 specific changes on verification and file selection
Changed : Selection order modified according last changes of build SDK's and vendor-specific cases
Changed : Scatter tab changes, specific to multi-storage selection and settings

Model DB
Changed : New agents included for Tecno, Infinix, Itel, Panasonic, Walton brands ( with different SoC lines in every )

Other
BugFix : Minor changes and fixes

Password for files: 12345678

Download link #1

Download link #2

Download link #3

Information about Infinity products support period renew due to situation with COVID-19