như tiêu đề chạy con 8800d rm 13 bị lỗi này là gì vậy ae.. Connection status: UHCI:HUB:USB 2.00 (Full-speed) Driver: WinUSB, ver: 3.5.1.0 , NTMP ver: 6.1.7601.17514 Module ver: 1.0.0.21762(03-12-2014), Library ver: 1.0.0.14473(03-12-2014) RPL backup already exist (C:\mobileEx\3.5\data\backup\35621600027479_BACK.r pl). Processing MCU file: rm13_33_11003.780 [TIKU BT2,TIKU ALGORITHM] size: 9.86 MB Supported Ids: 1052, 2051 ASIC ID: 0x1052 [TikuEdge ver: 1.1] SecondaryBoot: te_2nd.fia [TIKU BT2] version: 4.76.0 revision: 0.7 size: 0x2398 Supported Ids: 1051, 1052, 2051 FlashID0: 00EC 22F8 [Samsung K8S2815ETA,128 Mbits] page size: 64 K type: NOR area: 00000000-00FFFFFF FlashID1: 00EC 0020 [Samsung KFM1216Q2M,512 Mbits] type: NAND hw: EIJA(E) FlashID2: 0000 0001 [unused/removed] FlashID3: 0000 0001 [unused/removed] ExtBUSC: 0000 0000 18F0 9FE5 18F0 9FE5 18F0 9FE5 Algorithm: te_amd.fia [TIKU ALGORITHM] version: 4.76.0 revision: 0.7 size: 0x84D8 Supported Ids: 1051, 1052, 2051 Performing Flash Authentication ...OK UEM ID: 00426F71:BDB3DA60 Area [00000000-0000FFFF] erased in 0.630 s Area [00010000-009FFFFF] erased in 1 min 38.652 s Area [00A00000-00B3FFFF] erased in 12.373 s Area [00B60000-00FAFFFF] erased in 43.524 s Flash programming ... Programming completed in 1 min 7.835 s File processed in 3 min 52.330 s Processing CNT file: rm13_33_11003.78.ucp_x [TIKU BT2,TIKU MON CSM] size: 4.66 MB Supported Ids: 1052, 10C6, 2051 ASIC ID: 0x1052 [TikuEdge ver: 1.1] SecondaryBoot: te_2nd.fia [TIKU BT2] version: 4.76.0 revision: 0.7 size: 0x2398 Supported Ids: 1051, 1052, 2051 FlashID0: 00EC 22F8 [Samsung K8S2815ETA,128 Mbits] page size: 64 K type: NOR area: 00000000-00FFFFFF FlashID1: 00EC 0020 [Samsung KFM1216Q2M,512 Mbits] type: NAND hw: EIJA(E) FlashID2: 0000 0001 [unused/removed] FlashID3: 0000 0001 [unused/removed] ExtBUSC: 0000 0000 18F0 9FE5 18F0 9FE5 18F0 9FE5 Algorithm: te_oncsm.fia [TIKU MON CSM] version: 4.76.0 revision: 0.7 size: 0x5660 Supported Ids: 1051, 1052, 2051 Mass Memory Storage Device detected. Configuring MM bus ... Formating partition ...OK Opening MM device ... Erasing disks ...OK Flash programming ... The semaphore timeout period has expired Error while programming [2E] at 0x01000020, Result: 0000 flashing terminated !
