máy hư manfem thay màn k lên nguồn ..bấm nguồn cosdao động ..em fals mxbox báo Backup saved to "C:\mobileEx\3.5\data\backup\XGOLD_RM-908_3AF6460B0F8B6067_IMEI.back" MXKEY [MxKey Team HTI PLUS Flasher Interface 0], SN: C0880291 Using device: HTI, FW ver: 00.50, SN: 01010343 Connection status: EHCI:HUB:HUB:USB 2.00 (Full-speed) Driver: WinUSB, ver: 3.5.1.0 , NTMP ver: 6.1.7601.17514 Module ver: 1.0.0.21762(03-12-2014), Library ver: 1.0.0.14473(03-12-2014) Device synchronized. CPU: XGOLD 110 Using embedded SBL from MCU. Sending EBL Loader ...OK Sending EBL ...OK Getting EBL Version ... Boot mode: 0xCC EBL version major/minor: 10.27 EBL version: Default_RAM_Bootloader Set baud rate to: 921.60 Kbit/s Flash ID: 002C CB17 - 00000004 [Micron ] CFI information: Flash settings: 0/1, size: 0x00800000 2 Block regions: 127 x 0x00010000 = 0x007F0000 16 x 0x00001000 = 0x00010000 EBL ready ! Processing file: rm908_02.700 Downloading item CODE:hw_b1_rm908_02.700.fls, num block: 3, size: 4.20 MB Erasing area 0x00800000-0x00A0FFFE ...OK Programming completed in 35.110 s Erasing area 0x00C60000-0x00E8123E ...OK Programming completed in 35.478 s Erasing area 0x00FFC000-0x00FFC03E ...OK Programming completed in 0.138 s Error reading checksum! Total time for flashing process(boot+erase+write) was 2 min 11.222 s Phone type: RM-908 SW version: V 02.70 22-02-13 RM-908 (c) Nokia Imei plain: 35790105473829-7 Product code: 059R488 Cellular system: GSM ASIC ID: 0x2292, type: 11 Ppm Id: IJ Language Pack: - not available. Imei net: 35790105473829 Provider: GSM Test Operator Counter: 0/3, 0/10 CONFIG_DATA: 0010100000000000 PROFILE_BITS: 0000000000040002 BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
Backup already exists(C:\mobileEx\3.5\data\backup\XGOLD_RM-908_3AF6460B0F8B6067_IMEI.back) MXKEY [MxKey Team HTI PLUS Flasher Interface 0], SN: C0880291 Using device: HTI, FW ver: 00.50, SN: 01010343 Connection status: EHCI:HUB:HUB:USB 2.00 (Full-speed) Driver: WinUSB, ver: 3.5.1.0 , NTMP ver: 6.1.7601.17514 Module ver: 1.0.0.21762(03-12-2014), Library ver: 1.0.0.14473(03-12-2014) Device synchronized. CPU: XGOLD 110 Using embedded SBL from MCU. Sending EBL Loader ...OK Sending EBL ...OK Getting EBL Version ... Boot mode: 0xCC EBL version major/minor: 10.27 EBL version: Default_RAM_Bootloader Set baud rate to: 921.60 Kbit/s Flash ID: 002C CB17 - 00000004 [Micron ] CFI information: Flash settings: 0/1, size: 0x00800000 2 Block regions: 127 x 0x00010000 = 0x007F0000 16 x 0x00001000 = 0x00010000 EBL ready ! Processing file: rm908_02.700 Downloading item CODE:hw_b1_rm908_02.700.fls, num block: 3, size: 4.20 MB Erasing area 0x00800000-0x00A0FFFE ...OK Programming ... flashing terminated !
máy còn dao động là ok rồi,xem màn hàn ok chưa ? đo tổng trở chân tiếp xúc màn xem thế nào rùi tính tiếp. mấy dòng máy này không có màn hình vẫn flash ok
