Xin Log EMMC R831k

Lê Anh VF · 20/3/17 lúc 16:07

E có con R831k mà check ko ra...xin ae nào có con này read ra dùm e cái log với ah.e thay emmc mà ko có loại giống nên nhờ ae...thank mọi người

damxuanquang · 20/3/17 lúc 16:10

ko ra là nó ngỏm rồi bạn! kiếm con khác thay đi! kiếm con sasmung kmnjs...b205 á!

le ha nam · 20/3/17 lúc 16:28

Nguyên 1 mớ log thay emmc luôn :

3/15/2017 8:57:01 PM> Looking for EasyJTAG box...
3/15/2017 8:57:01 PM> EasyJTAG API ver. 2008
3/15/2017 8:57:01 PM> Setting IO Levels to 3.3V
3/15/2017 8:57:01 PM> Setting frequence to 14 Mhz
3/15/2017 8:57:01 PM> HiPower mode is OFF
3/15/2017 8:57:03 PM> OpenUSB returned = 0
3/15/2017 8:57:03 PM> Power Controller returned = 0
3/15/2017 8:57:03 PM> EasyJTAG Box Serial = 02000017CF291B82
3/15/2017 8:57:03 PM> EasyJTAG Box Firmware = 01.58
3/15/2017 8:57:03 PM> HiPower mode is OFF
3/15/2017 8:57:03 PM> CMD Pullup Level: 3145 mV
3/15/2017 8:57:03 PM> CMD Active Level: 3238 mV
3/15/2017 8:57:03 PM> eMMC Init returned = 0
3/15/2017 8:57:03 PM> EMMC Device Information :
3/15/2017 8:57:03 PM> EMMC CID: 1501004B3758564D42010D88D8E9519A
3/15/2017 8:57:03 PM> EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
3/15/2017 8:57:03 PM> EMMC Manufacture Name: SAMSUNG
3/15/2017 8:57:03 PM> EMMC Manufacture ID: 0x15 , OEM ID: 0100
3/15/2017 8:57:03 PM> EMMC Manufacture Date: 5/2014 , Rev: 01
3/15/2017 8:57:03 PM> EMMC NAME: K7XVMB , S/N: 0D88D8E9 , rev. 01
3/15/2017 8:57:03 PM> EMMC NAME (HEX): 4B3758564D42
3/15/2017 8:57:03 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
3/15/2017 8:57:03 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 8:57:03 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 512 KB (000000080000)
3/15/2017 8:57:03 PM> EMMC Permanent Write Protection: No
3/15/2017 8:57:03 PM> EMMC Temporary Write Protection: No
3/15/2017 8:57:03 PM> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
3/15/2017 8:57:03 PM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
3/15/2017 8:57:03 PM> Boot Bus Config: 0x00 , width 1bit
3/15/2017 8:57:03 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
3/15/2017 8:57:03 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
3/15/2017 8:57:03 PM> Device supports partitioning features
3/15/2017 8:57:03 PM> Device can have enhanced technological features in partitions and user data area
3/15/2017 8:57:03 PM> Device can have extended partitions attribute
3/15/2017 8:57:03 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
3/15/2017 8:57:03 PM> Backup saved: K7XVMB_0D88D8E9_20170315_205703.extcsd
3/15/2017 8:57:03 PM> EMMC Init completed.
3/15/2017 8:57:03 PM>
3/15/2017 8:57:03 PM> Operation: Changing BOOT and RPMB sizes ...
3/15/2017 8:57:03 PM> New BOOT size: 4096 Kb
3/15/2017 8:57:03 PM> New RPMB size: 4096 Kb
3/15/2017 8:57:03 PM>
3/15/2017 8:57:23 PM> Successfully
3/15/2017 8:57:23 PM>
3/15/2017 8:57:29 PM> Looking for EasyJTAG box...
3/15/2017 8:57:29 PM> EasyJTAG API ver. 2008
3/15/2017 8:57:29 PM> Setting IO Levels to 3.3V
3/15/2017 8:57:29 PM> Setting frequence to 14 Mhz
3/15/2017 8:57:29 PM> HiPower mode is OFF
3/15/2017 8:57:30 PM> OpenUSB returned = 0
3/15/2017 8:57:30 PM> Power Controller returned = 0
3/15/2017 8:57:30 PM> EasyJTAG Box Serial = 02000017CF291B82
3/15/2017 8:57:30 PM> EasyJTAG Box Firmware = 01.58
3/15/2017 8:57:30 PM> HiPower mode is OFF
3/15/2017 8:57:30 PM> CMD Pullup Level: 3155 mV
3/15/2017 8:57:30 PM> CMD Active Level: 3248 mV
3/15/2017 8:57:30 PM> eMMC Init returned = 0
3/15/2017 8:57:30 PM> EMMC Device Information :
3/15/2017 8:57:30 PM> EMMC CID: 1501004B3758564D42010D88D8E9519A
3/15/2017 8:57:30 PM> EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
3/15/2017 8:57:30 PM> EMMC Manufacture Name: SAMSUNG
3/15/2017 8:57:30 PM> EMMC Manufacture ID: 0x15 , OEM ID: 0100
3/15/2017 8:57:30 PM> EMMC Manufacture Date: 5/2014 , Rev: 01
3/15/2017 8:57:30 PM> EMMC NAME: K7XVMB , S/N: 0D88D8E9 , rev. 01
3/15/2017 8:57:30 PM> EMMC NAME (HEX): 4B3758564D42
3/15/2017 8:57:30 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
3/15/2017 8:57:30 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 8:57:30 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
3/15/2017 8:57:30 PM> EMMC Permanent Write Protection: No
3/15/2017 8:57:30 PM> EMMC Temporary Write Protection: No
3/15/2017 8:57:30 PM> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
3/15/2017 8:57:30 PM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
3/15/2017 8:57:30 PM> Boot Bus Config: 0x00 , width 1bit
3/15/2017 8:57:30 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
3/15/2017 8:57:30 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
3/15/2017 8:57:30 PM> Device supports partitioning features
3/15/2017 8:57:30 PM> Device can have enhanced technological features in partitions and user data area
3/15/2017 8:57:30 PM> Device can have extended partitions attribute
3/15/2017 8:57:30 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
3/15/2017 8:57:30 PM> Backup saved: K7XVMB_0D88D8E9_20170315_205730.extcsd
3/15/2017 8:57:30 PM> EMMC Init completed.
3/15/2017 8:57:30 PM>
3/15/2017 8:57:36 PM> Looking for EasyJTAG box...
3/15/2017 8:57:36 PM> EasyJTAG API ver. 2008
3/15/2017 8:57:36 PM> Setting IO Levels to 3.3V
3/15/2017 8:57:36 PM> Setting frequence to 14 Mhz
3/15/2017 8:57:36 PM> HiPower mode is OFF
3/15/2017 8:57:37 PM> OpenUSB returned = 0
3/15/2017 8:57:37 PM> Power Controller returned = 0
3/15/2017 8:57:37 PM> EasyJTAG Box Serial = 02000017CF291B82
3/15/2017 8:57:37 PM> EasyJTAG Box Firmware = 01.58
3/15/2017 8:57:37 PM> HiPower mode is OFF
3/15/2017 8:57:38 PM> CMD Pullup Level: 3155 mV
3/15/2017 8:57:38 PM> CMD Active Level: 3238 mV
3/15/2017 8:57:38 PM> eMMC Init returned = 0
3/15/2017 8:57:38 PM> EMMC Device Information :
3/15/2017 8:57:38 PM> EMMC CID: 1501004B3758564D42010D88D8E9519A
3/15/2017 8:57:38 PM> EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
3/15/2017 8:57:38 PM> EMMC Manufacture Name: SAMSUNG
3/15/2017 8:57:38 PM> EMMC Manufacture ID: 0x15 , OEM ID: 0100
3/15/2017 8:57:38 PM> EMMC Manufacture Date: 5/2014 , Rev: 01
3/15/2017 8:57:38 PM> EMMC NAME: K7XVMB , S/N: 0D88D8E9 , rev. 01
3/15/2017 8:57:38 PM> EMMC NAME (HEX): 4B3758564D42
3/15/2017 8:57:38 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
3/15/2017 8:57:38 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 8:57:38 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
3/15/2017 8:57:38 PM> EMMC Permanent Write Protection: No
3/15/2017 8:57:38 PM> EMMC Temporary Write Protection: No
3/15/2017 8:57:38 PM> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
3/15/2017 8:57:38 PM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
3/15/2017 8:57:38 PM> Boot Bus Config: 0x00 , width 1bit
3/15/2017 8:57:38 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
3/15/2017 8:57:38 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
3/15/2017 8:57:38 PM> Device supports partitioning features
3/15/2017 8:57:38 PM> Device can have enhanced technological features in partitions and user data area
3/15/2017 8:57:38 PM> Device can have extended partitions attribute
3/15/2017 8:57:38 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
3/15/2017 8:57:38 PM> Backup saved: K7XVMB_0D88D8E9_20170315_205738.extcsd
3/15/2017 8:57:38 PM> EMMC Init completed.
3/15/2017 8:57:38 PM>
3/15/2017 8:57:38 PM> Erasing for: ROM1 , start: 0x000000000000 , size: 0x0001D2000000
3/15/2017 8:57:38 PM> eMMC switching to ROM1
3/15/2017 8:57:38 PM> Erasing partition...
3/15/2017 9:01:48 PM> Done erasing partition.
3/15/2017 9:01:48 PM>
3/15/2017 9:05:43 PM> Looking for EasyJTAG box...
3/15/2017 9:05:43 PM> EasyJTAG API ver. 2008
3/15/2017 9:05:43 PM> Setting IO Levels to 3.3V
3/15/2017 9:05:43 PM> Setting frequence to 14 Mhz
3/15/2017 9:05:43 PM> HiPower mode is OFF
3/15/2017 9:05:44 PM> OpenUSB returned = 0
3/15/2017 9:05:44 PM> Power Controller returned = 0
3/15/2017 9:05:44 PM> EasyJTAG Box Serial = 02000017CF291B82
3/15/2017 9:05:44 PM> EasyJTAG Box Firmware = 01.58
3/15/2017 9:05:44 PM> HiPower mode is OFF
3/15/2017 9:05:44 PM> CMD Pullup Level: 3155 mV
3/15/2017 9:05:44 PM> CMD Active Level: 3238 mV
3/15/2017 9:05:44 PM> eMMC Init returned = 0
3/15/2017 9:05:44 PM> EMMC Device Information :
3/15/2017 9:05:44 PM> EMMC CID: 1501004B3758564D42010D88D8E9519A
3/15/2017 9:05:44 PM> EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
3/15/2017 9:05:44 PM> EMMC Manufacture Name: SAMSUNG
3/15/2017 9:05:44 PM> EMMC Manufacture ID: 0x15 , OEM ID: 0100
3/15/2017 9:05:44 PM> EMMC Manufacture Date: 5/2014 , Rev: 01
3/15/2017 9:05:44 PM> EMMC NAME: K7XVMB , S/N: 0D88D8E9 , rev. 01
3/15/2017 9:05:44 PM> EMMC NAME (HEX): 4B3758564D42
3/15/2017 9:05:44 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
3/15/2017 9:05:44 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:44 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:44 PM> EMMC Permanent Write Protection: No
3/15/2017 9:05:44 PM> EMMC Temporary Write Protection: No
3/15/2017 9:05:44 PM> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
3/15/2017 9:05:44 PM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
3/15/2017 9:05:44 PM> Boot Bus Config: 0x00 , width 1bit
3/15/2017 9:05:44 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
3/15/2017 9:05:44 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
3/15/2017 9:05:44 PM> Device supports partitioning features
3/15/2017 9:05:44 PM> Device can have enhanced technological features in partitions and user data area
3/15/2017 9:05:44 PM> Device can have extended partitions attribute
3/15/2017 9:05:44 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
3/15/2017 9:05:44 PM> Backup saved: K7XVMB_0D88D8E9_20170315_210544.extcsd
3/15/2017 9:05:44 PM> EMMC Init completed.
3/15/2017 9:05:44 PM>
3/15/2017 9:05:44 PM> Opening file: C:\Users\Administrator\Downloads\[vnROM.net]_Oppo_Joy3_A11w_MT6582\MT6582_Android_scatter.txt
3/15/2017 9:05:44 PM>
3/15/2017 9:05:44 PM> The new format of scatter
3/15/2017 9:05:44 PM> config_version: V1.1.1
3/15/2017 9:05:44 PM> platform: MT6582
3/15/2017 9:05:44 PM> preloader.bin
3/15/2017 9:05:44 PM> Found 5 supported eMMC CID:
3/15/2017 9:05:44 PM> name = 'KJS00M' hex = 0x4B4A5330304D [SAMSUNG]
3/15/2017 9:05:44 PM> name = 'H4G1d' hex = 0x483447316404 [SKHYNIX]
3/15/2017 9:05:44 PM> name = 'H8G2d' hex = 0x483847326404 [SKHYNIX]
3/15/2017 9:05:44 PM> name = 'P1J94L' hex = 0x50314A39344C [MICRON]
3/15/2017 9:05:44 PM> name = 'H4G2a' hex = 0x483447326111 [SKHYNIX]
3/15/2017 9:05:44 PM>
3/15/2017 9:05:44 PM> The size of the last section has been updated
3/15/2017 9:05:48 PM>
3/15/2017 9:05:48 PM> Looking for EasyJTAG box...
3/15/2017 9:05:48 PM> EasyJTAG API ver. 2008
3/15/2017 9:05:48 PM> Setting IO Levels to 3.3V
3/15/2017 9:05:48 PM> Setting frequence to 14 Mhz
3/15/2017 9:05:48 PM> HiPower mode is OFF
3/15/2017 9:05:49 PM> OpenUSB returned = 0
3/15/2017 9:05:49 PM> Power Controller returned = 0
3/15/2017 9:05:49 PM> EasyJTAG Box Serial = 02000017CF291B82
3/15/2017 9:05:49 PM> EasyJTAG Box Firmware = 01.58
3/15/2017 9:05:49 PM> HiPower mode is OFF
3/15/2017 9:05:49 PM> CMD Pullup Level: 3155 mV
3/15/2017 9:05:49 PM> CMD Active Level: 3248 mV
3/15/2017 9:05:49 PM> eMMC Init returned = 0
3/15/2017 9:05:49 PM> EMMC Device Information :
3/15/2017 9:05:49 PM> EMMC CID: 1501004B3758564D42010D88D8E9519A
3/15/2017 9:05:49 PM> EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
3/15/2017 9:05:49 PM> EMMC Manufacture Name: SAMSUNG
3/15/2017 9:05:49 PM> EMMC Manufacture ID: 0x15 , OEM ID: 0100
3/15/2017 9:05:49 PM> EMMC Manufacture Date: 5/2014 , Rev: 01
3/15/2017 9:05:49 PM> EMMC NAME: K7XVMB , S/N: 0D88D8E9 , rev. 01
3/15/2017 9:05:49 PM> EMMC NAME (HEX): 4B3758564D42
3/15/2017 9:05:49 PM> EMMC ROM 1 (Main User Data) Capacity: 7456 MB (0001D2000000)
3/15/2017 9:05:49 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:49 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:49 PM> EMMC Permanent Write Protection: No
3/15/2017 9:05:49 PM> EMMC Temporary Write Protection: No
3/15/2017 9:05:49 PM> Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
3/15/2017 9:05:49 PM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
3/15/2017 9:05:49 PM> Boot Bus Config: 0x00 , width 1bit
3/15/2017 9:05:49 PM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
3/15/2017 9:05:49 PM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
3/15/2017 9:05:49 PM> Device supports partitioning features
3/15/2017 9:05:49 PM> Device can have enhanced technological features in partitions and user data area
3/15/2017 9:05:49 PM> Device can have extended partitions attribute
3/15/2017 9:05:49 PM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
3/15/2017 9:05:49 PM> Backup saved: K7XVMB_0D88D8E9_20170315_210549.extcsd
3/15/2017 9:05:49 PM> EMMC Init completed.
3/15/2017 9:05:49 PM>
3/15/2017 9:05:49 PM> Repairing eMMC CID...
3/15/2017 9:05:49 PM>
3/15/2017 9:05:50 PM> Success! Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to finalize CID Patch !
3/15/2017 9:05:50 PM>

viettinh · 20/3/17 lúc 16:50

Lê Anh VF nói: ↑
E có con R831k mà check ko ra...xin ae nào có con này read ra dùm e cái log với ah.e thay emmc mà ko có loại giống nên nhờ ae...thank mọi người
Click to expand...

Fix cho giống cái này thôi mà

3/15/2017 9:05:49 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:49 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)

Thêm đổi CID cho phù hợp bản rom.
Còn lại cứ bấm Mediatek là dc.

Lê Anh VF · 20/3/17 lúc 17:32

viettinh nói: ↑
Fix cho giống cái này thôi mà

3/15/2017 9:05:49 PM> EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
3/15/2017 9:05:49 PM> EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)

Thêm đổi CID cho phù hợp bản rom.
Còn lại cứ bấm Mediatek là dc.
Click to expand...

a ơi e ko hiểu cid là gì,có phải là cái này ko a?
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)

e đang tìm cái log chuẩn của r831k để change emmc new cho giống ah a

duythangvn · 20/3/17 lúc 17:50

Lê Anh VF nói: ↑
a ơi e ko hiểu cid là gì,có phải là cái này ko a?
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)

e đang tìm cái log chuẩn của r831k để change emmc new cho giống ah a
Click to expand...

EMMC CID: 1501004B3758564D42010D88D8E9519A

Lê Anh VF · 20/3/17 lúc 17:52

duythangvn nói: ↑
EMMC CID: 1501004B3758564D42010D88D8E9519A
Click to expand...

cái mã nó thế thì mình edit emmc new cho giống vậy luôn hả a @@

Quoc_TraVinh · 20/3/17 lúc 18:15

Lê Anh VF nói: ↑
cái mã nó thế thì mình edit emmc new cho giống vậy luôn hả a @@
Click to expand...

Xem lại bài của MOD Bi_Sony hướng dẫn cụ thể phần này.thường emmc samsung easy plus nó tự động change CID

viettinh · 21/3/17 lúc 12:19

Lê Anh VF nói: ↑
a ơi e ko hiểu cid là gì,có phải là cái này ko a?
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)

e đang tìm cái log chuẩn của r831k để change emmc new cho giống ah a
Click to expand...

Cái đó là phân vùng boot.
Khi chọn Mediatek thì tool sẽ tự động set phân vùng boot này cho EMMC rồi.

Xin Log EMMC R831k

Lê Anh VF

No Life Poster

damxuanquang

No Life Poster

le ha nam

Junior Member

viettinh

No Life Poster

Lê Anh VF

No Life Poster

duythangvn

Major Poster

Lê Anh VF

No Life Poster

Quoc_TraVinh

Crazy Poster

viettinh

No Life Poster

Chia sẻ trang này

Tìm kiếm hữu ích

Xin Log EMMC R831k

No Life Poster

No Life Poster

Junior Member

No Life Poster

No Life Poster

Major Poster

No Life Poster

Crazy Poster

No Life Poster

Chia sẻ trang này